HYDAC · Betamicron 4 D/DN · pressure line

0660 D 010 BH4HC filter element: specifications & equivalents

Q: What are the dimensions of the 0660 D 010 BH4HC filter element?

The published envelope is 91.4 mm OD × 330.2 mm length with a 48 mm inside diameter (3.598 × 13.000 in × 1.890 in ID). Confirm against the housing drawing before ordering.

Q: What micron rating does 0660 D 010 BH4HC use?

This element is rated 10 µm absolute — ßx(c) ≥ 1000 (HYDAC grade convention: β12(c) ≥ 1000). Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

The 0660 D 010 BH4HC is a HYDAC pressure-line hydraulic filter element, built with bh/hc=betamicron® high collapse media, sized 91.4 × 330.2 mm OD × length (ID 48 mm), rated at 10 µm absolute (ßx(c) ≥ 1000 (HYDAC grade convention: β12(c) ≥ 1000)). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 91.4 × 330.2 mm

Inside diameter 48 mm

Filtration rating 10 µm abs.

Beta rating ßx(c) ≥ 1000 (HYDAC grade convention: β12(c) ≥ 1000)

Media BH/HC=Betamicron® High Collapse

Collapse / burst 210 bar

Line type pressure

Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-09-28. Confidence score 0.92.

Dimensions, ratings and seal compound are taken directly from the HYDAC electronic catalog (catalog.hydac.com). Outside diameter and length are converted from the inch values printed on the catalog page; verify against the current HYDAC data sheet before ordering.

Specification table

Parameter	Value
Filter type	pressure line
Media	BH/HC=Betamicron® High Collapse
Filtration rating	10 µm
Rating basis	absolute
Beta ratio	ßx(c) ≥ 1000 (HYDAC grade convention: β12(c) ≥ 1000)
Outside diameter OD	91.4 mm
Inside diameter ID	48 mm
Length	330.2 mm
End caps	open-ended cartridge element
Flow direction	outside-in
Collapse / burst pressure	210 bar
Integral bypass valve	none (housing/valve-dependent)
Seal material	Nitrile (Buna-N)
Operating temperature	-30 to 100 °C
Source catalog	HYDAC Technology Corporation: HYDAC electronic product catalog (catalog.hydac.com)
Last verified	2026-09-28

Sources: HYDAC Technology Corporation — HYDAC electronic product catalog (catalog.hydac.com) — accessed 2026-10-16.

HYDAC® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized HYDAC distributor.

Dimensional drawing

Reference drawing generated from the source values cited on this page — nominal envelope, schematic section, not a manufacturer drawing. The PDF is A3 landscape and vector; the PNG is sized for a WhatsApp preview. Confirm thread, end caps, seal compound and micron/Beta grade against the original element before ordering.

Dimensions & series range

Outside diameter	91.4 mm (3.598 in)
Inside diameter	48 mm (1.890 in)
Overall length	330.2 mm (13.000 in)

All 91×330 mm interchange elements →

Cross references & equivalents

Equivalent model	Brand	Match level	Note
↔ 02.0660D.10VG.HR.HC.E.P	Eaton / Internormen	partial	Eaton's filtration cross-reference lists 0660D010BH4HC (Hydac) as an interchange for 02.0660D.10VG.HR.HC.E.P. Envelope cross-reference; verify micron grade, delta-P rating and seal configuration before substituting.
↔ DHD660H10B	Filtrec	partial	Filtrec's official Cross Navigator maps HYDAC 0660D010BH4HC to FILTREC DHD660H10B as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade. Rated micron differs (10 vs 12 µm) — verify efficiency class and collapse/seal for the housing before substituting.
↔ SBF-0661D-Z10B	Schroeder Industries	partial	Schroeder online cross-reference (HYDAC); envelope match — verify grade and seals.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

Full chart: HYDAC cross reference chart →

How the 0660 D 010 BH4HC model number is decoded

0660 D 010 BH4HCHYDAC Type D filter element ordering code per the HYDAC electronic catalog (s16).
BH/HC=Betamicron® High CollapseFilter media and collapse family as printed in the catalog.
10 µmAbsolute filter rating per the HYDAC catalog.
ßx(c) ≥ 1000Beta ratio rating as printed in the catalog.
91.4 mmOutside diameter.
48 mmInner diameter.
330.2 mmElement length.
210 barElement collapse (differential pressure) rating.
Nitrile (Buna-N)Seal compound.

Typical equipment & applications

Pressure-line filtration for HYDAC DF/DFF and equivalent housings
Industrial and mobile hydraulic systems

Selection pitfalls — read before you substitute

Line type is not interchangeable: return-line cartridges are low-collapse executions that typically tolerate roughly 10–20 bar differential, while pressure-line elements are commonly rated 100–210 bar. Installing a low-collapse element in a pressure housing can rupture the media on cold-start spikes.
“10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
This execution uses nitrile (buna-n) seals — verify the compound against the fluid data sheet: standard nitrile (NBR) can fail early in phosphate-ester fluids and at sustained high temperature, where fluorocarbon/Viton executions may be required.
End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.

Frequently asked questions

What are the dimensions of the 0660 D 010 BH4HC filter element?

The published envelope is 91.4 mm OD × 330.2 mm length with a 48 mm inside diameter (3.598 × 13.000 in × 1.890 in ID). Confirm against the housing drawing before ordering.

What micron rating does 0660 D 010 BH4HC use?

This element is rated 10 µm absolute — ßx(c) ≥ 1000 (HYDAC grade convention: β12(c) ≥ 1000). Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

What replaces the 0660 D 010 BH4HC filter element?

3 partial match(es) requiring parameter review

How do I read the 0660 D 010 BH4HC part number?

See the designation decoder above: each segment of 0660D010BH4HC encodes size, line type, filtration grade and media/collapse execution.

Is a same-envelope aftermarket element always a drop-in replacement?

No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.

How often should a hydraulic filter element be replaced?

Replace at the housing manufacturer’s recommended differential-pressure setting (commonly signalled by a clogging indicator), or on a time-based service interval when no indicator is fitted — never wait for bypass to open continuously, because unfiltered oil then reaches the valves.

Same-envelope elements from other brands

View full interchange →

These 41 catalog element(s) share the 91×330 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

HF30100 Fleetguard HF30279 Fleetguard HF30505 Fleetguard 0660 D 001 BH4HC /-SFREE HYDAC · 1 µm 0660 D 001 ON HYDAC · 1 µm 0660 D 003 BH4HC HYDAC · 3 µm 0660 D 003 BH4HC /-V HYDAC · 3 µm 0660 D 003 OH/PS HYDAC · 3 µm 0660 D 003 ON HYDAC · 3 µm 0660 D 003 ON/PS HYDAC · 3 µm

Other models in the Betamicron 4 D/DN series

All 897 (list page 1/2) →

0015 D 010 BN4HC 35×42 mm · 10 µm 0030 D 003 BH4HC 36×94 mm · 3 µm 0030 D 003 BH4HC /-V 36×94 mm · 3 µm 0030 D 003 BN4HC 36×94 mm · 3 µm 0030 D 003 BN4HC /-V 36×94 mm · 3 µm 0030 D 005 BH4HC 36×94 mm · 5 µm 0030 D 005 BH4HC /-V 36×94 mm · 5 µm 0030 D 005 BN4HC 36×94 mm · 5 µm 0030 D 010 BH4HC 36×94 mm · 10 µm 0030 D 010 BN4HC 36×94 mm · 10 µm

Reviewed & verified by the ElementRef engineering desk against HYDAC Technology Corporation on 2026-09-28. Read our editorial & correction policy.