Filtrec · Filtrec elements · inline line

R710G03 filter element: specifications & equivalents

Q: What are the dimensions of the R710G03 filter element?

The published envelope is 72 mm OD × 55 mm length with a 45 mm inside diameter (2.835 × 2.165 in × 1.772 in ID). Confirm against the housing drawing before ordering.

Q: What micron rating does R710G03 use?

This element is rated 5 µm absolute — β5(c)≥1000. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

The R710G03 is a Filtrec inline-line hydraulic filter element, built with glassfiber media, sized 72 × 55 mm OD × length (ID 45 mm), rated at 5 µm absolute (β5(c)≥1000). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 72 × 55 mm

Inside diameter 45 mm

Filtration rating 5 µm abs.

Beta rating β 5(c)≥1000

Media glassfiber

Line type inline

Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-10-03. Confidence score 0.90.

Dimensions and media grade are taken from Filtrec’s official Cross Navigator, which maps this element to specific competitor part numbers. Filtrec does not publish collapse pressure or seal compound in this API for every code — verify collapse rating, seal execution and bypass setting against the current Filtrec data sheet for the target housing before ordering.

Specification table

Parameter	Value
Filter type	inline line
Media	glassfiber
Filtration rating	5 µm
Rating basis	absolute
Beta ratio	β5(c)≥1000
Outside diameter OD	72 mm
Inside diameter ID	45 mm
Length	55 mm
Integral bypass valve	none (housing/valve-dependent)
Manufacturer part no.	R710G03
Source catalog	Filtrec S.p.A.: Filtrec Cross Navigator
Last verified	2026-10-03

Sources: Filtrec S.p.A. — Filtrec Cross Navigator — accessed 2026-10-03.

Filtrec® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized Filtrec distributor.

Dimensional drawing

Reference drawing generated from the source values cited on this page — nominal envelope, schematic section, not a manufacturer drawing. The PDF is A3 landscape and vector; the PNG is sized for a WhatsApp preview. Confirm thread, end caps, seal compound and micron/Beta grade against the original element before ordering.

Dimensions & series range

Outside diameter	72 mm (2.835 in)
Inside diameter	45 mm (1.772 in)
Overall length	55 mm (2.165 in)

All 72×55 mm interchange elements →

Cross references & equivalents

Equivalent model	Brand	Match level	Note
↔ TXWCC3 page in verification queue	Aftermarket	full	Filtrec's official Cross Navigator maps FAIREY ARLON TXWCC3 to FILTREC R710G03 as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade.
↔ RA-030-E-03-B	STAUFF	partial	STAUFF Filter Interchange lists R710G03 (FILTREC) as replaced by RA-030-E-03-B. Envelope dimensions are published; media grade and performance data are not — confirm before substituting in cleanliness-critical circuits.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

Full chart: Filtrec cross reference chart →

How the R710G03 model number is decoded

G03Filtrec internal media grade code (glassfiber, 5 µm).

Typical equipment & applications

Filtrec aftermarket replacement hydraulic/lube filter element (R family), form-fit-function cross-referenced in Filtrec's official Cross Navigator.

Selection pitfalls — read before you substitute

“10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
Fine 5 µm media loads faster and runs at a higher cold Δp than coarser grades — only downgrade cleanliness targets if the system ISO 4406 code allows it.

Frequently asked questions

What are the dimensions of the R710G03 filter element?

The published envelope is 72 mm OD × 55 mm length with a 45 mm inside diameter (2.835 × 2.165 in × 1.772 in ID). Confirm against the housing drawing before ordering.

What micron rating does R710G03 use?

This element is rated 5 µm absolute — β5(c)≥1000. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

What replaces the R710G03 filter element?

1 catalog-confirmed full match(es) (TXWCC3); 1 partial match(es) requiring parameter review

Is a same-envelope aftermarket element always a drop-in replacement?

No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.

Same-envelope elements from other brands

View full interchange →

These 11 catalog element(s) share the 72×55 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

R700C10 Filtrec · 10 µm R710C10 Filtrec · 10 µm R710G06 Filtrec · 7 µm R710G10 Filtrec · 12 µm R710G25 Filtrec · 22 µm R710T25 Filtrec · 25 µm R710T60 Filtrec · 60 µm RA-030-E-03-B STAUFF RA-030-E-10-B STAUFF RA-030-E-20-B STAUFF

Other models in the Filtrec elements series

All 9874 (list page 11/20) →

A105C05 96×60 mm · 5 µm A105C10 96×60 mm · 10 µm A105C25 96×60 mm · 25 µm A105G03 96×60 mm · 5 µm A105G06 96×60 mm · 7 µm A105G10 96×60 mm · 12 µm A105G25 96×60 mm · 22 µm A105T125 96×60 mm · 125 µm A105T250 96×60 mm · 250 µm A105T60 96×60 mm · 60 µm

Reviewed & verified by the ElementRef engineering desk against Filtrec S.p.A. on 2026-10-03. Read our editorial & correction policy.