Filtrec · Filtrec elements · inline line

R480G03 filter element: specifications & equivalents

Q: What are the dimensions of the R480G03 filter element?

The published envelope is 70 mm OD × 122 mm length with a 33.5 mm inside diameter (2.756 × 4.803 in × 1.319 in ID). Confirm against the housing drawing before ordering.

Q: What micron rating does R480G03 use?

This element is rated 5 µm absolute — β5(c)≥1000. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

The R480G03 is a Filtrec inline-line hydraulic filter element, built with glassfiber media, sized 70 × 122 mm OD × length (ID 33.5 mm), rated at 5 µm absolute (β5(c)≥1000). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 70 × 122 mm

Inside diameter 33.5 mm

Filtration rating 5 µm abs.

Beta rating β 5(c)≥1000

Media glassfiber

Line type inline

Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-10-03. Confidence score 0.90.

Dimensions and media grade are taken from Filtrec’s official Cross Navigator, which maps this element to specific competitor part numbers. Filtrec does not publish collapse pressure or seal compound in this API for every code — verify collapse rating, seal execution and bypass setting against the current Filtrec data sheet for the target housing before ordering.

Specification table

Parameter	Value
Filter type	inline line
Media	glassfiber
Filtration rating	5 µm
Rating basis	absolute
Beta ratio	β5(c)≥1000
Outside diameter OD	70 mm
Inside diameter ID	33.5 mm
Length	122 mm
Integral bypass valve	none (housing/valve-dependent)
Manufacturer part no.	R480G03
Source catalog	Filtrec S.p.A.: Filtrec Cross Navigator
Last verified	2026-10-03

Sources: Filtrec S.p.A. — Filtrec Cross Navigator — accessed 2026-10-03.

Filtrec® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized Filtrec distributor.

Dimensional drawing

Reference drawing generated from the source values cited on this page — nominal envelope, schematic section, not a manufacturer drawing. The PDF is A3 landscape and vector; the PNG is sized for a WhatsApp preview. Confirm thread, end caps, seal compound and micron/Beta grade against the original element before ordering.

Dimensions & series range

Outside diameter	70 mm (2.756 in)
Inside diameter	33.5 mm (1.319 in)
Overall length	122 mm (4.803 in)

All 70×122 mm interchange elements →

Cross references & equivalents

Equivalent model	Brand	Match level	Note
↔ HC6200FCP4H	Pall	full	Filtrec's official Cross Navigator maps PALL HC6200FCP4H to FILTREC R480G03 as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade.
↔ HC6200FKP4H	Pall	full	Filtrec's official Cross Navigator maps PALL HC6200FKP4H to FILTREC R480G03 as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade.
↔ SBF-6200-4Z3B	Schroeder Industries	full	Filtrec's official Cross Navigator maps SCHROEDER SBF62004Z3B to FILTREC R480G03 as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

Full chart: Filtrec cross reference chart →

How the R480G03 model number is decoded

G03Filtrec internal media grade code (glassfiber, 5 µm).

Typical equipment & applications

Filtrec aftermarket replacement hydraulic/lube filter element (R family), form-fit-function cross-referenced in Filtrec's official Cross Navigator.

Selection pitfalls — read before you substitute

“10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
Fine 5 µm media loads faster and runs at a higher cold Δp than coarser grades — only downgrade cleanliness targets if the system ISO 4406 code allows it.

Frequently asked questions

What are the dimensions of the R480G03 filter element?

The published envelope is 70 mm OD × 122 mm length with a 33.5 mm inside diameter (2.756 × 4.803 in × 1.319 in ID). Confirm against the housing drawing before ordering.

What micron rating does R480G03 use?

This element is rated 5 µm absolute — β5(c)≥1000. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

What replaces the R480G03 filter element?

3 catalog-confirmed full match(es) (HC6200FCP4H, HC6200FKP4H, SBF-6200-4Z3B)

Is a same-envelope aftermarket element always a drop-in replacement?

No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.

Same-envelope elements from other brands

View full interchange →

These 11 catalog element(s) share the 70×122 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

R480G03V Filtrec · 5 µm R480G03V/ESD Filtrec · 5 µm R480G06 Filtrec · 7 µm R480G06V Filtrec · 7 µm R480G06V/ESD Filtrec · 7 µm R480G10 Filtrec · 12 µm R480G10V Filtrec · 12 µm R480G10V/ESD Filtrec · 12 µm R480G25 Filtrec · 22 µm R480G25V Filtrec · 22 µm

Other models in the Filtrec elements series

All 9874 (list page 11/20) →

A105C05 96×60 mm · 5 µm A105C10 96×60 mm · 10 µm A105C25 96×60 mm · 25 µm A105G03 96×60 mm · 5 µm A105G06 96×60 mm · 7 µm A105G10 96×60 mm · 12 µm A105G25 96×60 mm · 22 µm A105T125 96×60 mm · 125 µm A105T250 96×60 mm · 250 µm A105T60 96×60 mm · 60 µm

Reviewed & verified by the ElementRef engineering desk against Filtrec S.p.A. on 2026-10-03. Read our editorial & correction policy.