Donaldson · Hydraulic Catalog · inline line

P568818 filter element: specifications & equivalents

Q: What micron rating does P568818 use?

This element is rated 4 µm (nominal class). Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

The P568818 is a Donaldson inline-line hydraulic filter element, built with wire mesh media, rated at 4 µm class. Verify against the current manufacturer data sheet before ordering.

Filtration rating 4 µm nom.

Media Wire Mesh

Line type inline

Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-09-28. Confidence score 0.90.

OD/ID dimensions, collapse pressure and bypass settings are not printed in the filter-element choice table and are pending extraction from the housing dimension pages. Verify against the current Donaldson data sheet before ordering.

Specification table

Parameter	Value
Filter type	inline line
Media	Wire Mesh
Filtration rating	4 µm
Rating basis	nominal
Length	698 mm
Integral bypass valve	none (housing/valve-dependent)
Manufacturer part no.	P568818
Source catalog	Donaldson Company: Hydraulic Filtration Product Guide (F112100-ENG)
Last verified	2026-09-28

Sources: Donaldson Company — Hydraulic Filtration Product Guide (F112100-ENG) — accessed 2026-09-27.

Donaldson® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized Donaldson distributor.

Cross references & equivalents

Equivalent model	Brand	Match level	Note
↔ D652G03A	Filtrec	partial	Filtrec's official Cross Navigator maps DONALDSON P568818 to FILTREC D652G03A as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade. Rated micron differs (4 vs 5 µm) — verify efficiency class and collapse/seal for the housing before substituting.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

Full chart: Donaldson cross reference chart →

How the P568818 model number is decoded

P568818Donaldson hydraulic filter element part number per the Hydraulic Filtration Product Guide (F112100-ENG).
DT Product family: DT .
Wire MeshFilter media: Wire Mesh.
4 μmNominal filtration rating at βx(c) = 2 per ISO 16889.

Typical equipment & applications

Donaldson DT hydraulic filter housing

Selection pitfalls — read before you substitute

“10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
Fine 4 µm media loads faster and runs at a higher cold Δp than coarser grades — only downgrade cleanliness targets if the system ISO 4406 code allows it.

Frequently asked questions

What micron rating does P568818 use?

This element is rated 4 µm (nominal class). Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

What replaces the P568818 filter element?

1 partial match(es) requiring parameter review

How do I read the P568818 part number?

See the designation decoder above: each segment of P568818 encodes size, line type, filtration grade and media/collapse execution.

Other models in the Hydraulic Catalog series

All 360 →

P160700 150 µm P161016 4 µm P161571 22 µm P162233 75 µm P163542 11 µm P163567 23 µm P163945 150 µm P164056 13 µm P164059 22 µm P164405 4 µm

Reviewed & verified by the ElementRef engineering desk against Donaldson Company on 2026-09-28. Read our editorial & correction policy.