WIX Filters · 57xxx · return line
57410 filter element: specifications & equivalents
The 57410 is a WIX Filters return-line hydraulic filter element, built with paper media, sized 94 × 183 mm OD × length, rated at 5 µm class. Verify against the current manufacturer data sheet before ordering.
Envelope OD × L 94 × 183 mm
Filtration rating 5 µm nom.
Media Paper
Collapse / burst 55.158 bar
Line type return
Catalog verified. Parameters extracted from the manufacturer’s electronic
catalog / official interchange document and checked 2026-09-27. Confidence score 0.90.
Specification table
| Parameter | Value |
|---|---|
| Filter type | return line |
| Media | Paper |
| Filtration rating | 5 µm |
| Rating basis | nominal |
| Outside diameter OD | 94 mm |
| Length | 183 mm |
| End caps | open-ended cartridge element (no baseplate) |
| Flow direction | outside-in |
| Collapse / burst pressure | 55.158 bar |
| Integral bypass valve | opens at 1.4 bar |
| Seal material | Nitrile (NBR) |
| Manufacturer part no. | 57410 |
| Source catalog | WIX Filters (MANN+HUMMEL): WIX Filters online product catalog |
| Last verified | 2026-09-27 |
Sources: WIX Filters (MANN+HUMMEL) — WIX Filters online product catalog — accessed 2026-09-26.
WIX Filters® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized WIX Filters distributor.
Dimensions & series range
| Outside diameter | 94 mm (3.701 in) |
| Overall length | 183 mm (7.205 in) |
Cross references & equivalents
No catalog-verified cross references yet. This model is in the manual verification queue — request a verified equivalent.
Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 57410 model number is decoded
- 57410WIX hydraulic cartridge element part number.
- 94 mm OD / undefined mm IDCartridge envelope (outside/inside diameter); no mounting thread.
- PaperFilter media: Paper.
Typical equipment & applications
- Mobile and industrial hydraulic return circuits
- Construction and agricultural equipment
- Heavy-duty transmission and torque-converter circuits
Selection pitfalls — read before you substitute
- A return-line element is not a pressure-line element: return cartridges (low-collapse) tolerate roughly 20 bar differential, while BH4HC pressure executions are rated to 210 bar. Installing a low-collapse element in a pressure housing can rupture the media on cold-start spikes.
- This execution carries an integral bypass valve (opens at 1.4 bar). The same envelope also exists without it, relying on the housing valve. Mixing the two strategies changes cold-start protection — match what was installed originally.
- “10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
- Nitrile (NBR) seals are standard for mineral hydraulic oil but fail early in some phosphate-ester fluids and at sustained high temperature; verify seal compound against the fluid data sheet (fluorocarbon/Viton executions may be required).
- Fine 5 µm media loads faster and runs at a higher cold Δp than coarser grades — only downgrade cleanliness targets if the system ISO 4406 code allows it.
- End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.
Frequently asked questions
What are the dimensions of the 57410 filter element?
The published envelope is 94 mm OD × 183 mm length (3.701 × 7.205 in). Confirm against the housing drawing before ordering.
What micron rating does 57410 use?
This element is rated 5 µm (nominal class). Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.
What replaces the 57410 filter element?
Cross references are being verified for this model — use the inquiry form and the engineering desk will confirm equivalents.
How do I read the 57410 part number?
See the designation decoder above: each segment of 57410 encodes size, line type, filtration grade and media/collapse execution.
Is a same-envelope aftermarket element always a drop-in replacement?
No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.
How often should a hydraulic return-line element be replaced?
Replace at the housing manufacturer’s recommended differential-pressure setting (commonly signalled by a clogging indicator), or on a time-based service interval when no indicator is fitted — never wait for bypass to open continuously, because unfiltered oil then reaches the valves.
Other models in the 57xxx series
All 221 →Reviewed & verified by the ElementRef engineering desk against WIX Filters (MANN+HUMMEL) on 2026-09-27. Read our editorial & correction policy.