ElementBase

WIX Filters · 57xxx · return line

57108 filter element: specifications & equivalents

The 57108 is a WIX Filters return-line hydraulic filter element, built with paper media, sized 150 × 451 mm OD × length (ID 110 mm). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 150 × 451 mm
Inside diameter 110 mm
Media Paper
Line type return
Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-09-27. Confidence score 0.90.

Specification table

ParameterValue
Filter type return line
Media Paper
Rating basis nominal
Outside diameter OD 150 mm
Inside diameter ID 110 mm
Length 451 mm
End caps open-ended cartridge element (no baseplate)
Flow direction outside-in
Integral bypass valve none (housing/valve-dependent)
Seal material Nitrile (NBR)
Manufacturer part no. 57108
Source catalog WIX Filters (MANN+HUMMEL): WIX Filters online product catalog
Last verified2026-09-27

Sources: WIX Filters (MANN+HUMMEL) — WIX Filters online product catalog — accessed 2026-09-26.

WIX Filters® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized WIX Filters distributor.

Dimensions & series range

Outside diameter150 mm (5.906 in)
Inside diameter110 mm (4.331 in)
Overall length451 mm (17.756 in)

All 150×451 mm interchange elements →

Cross references & equivalents

No catalog-verified cross references yet. This model is in the manual verification queue — request a verified equivalent.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 57108 model number is decoded

  • 57108WIX hydraulic cartridge element part number.
  • 150 mm OD / 110 mm IDCartridge envelope (outside/inside diameter); no mounting thread.
  • PaperFilter media: Paper.

Typical equipment & applications

  • Mobile and industrial hydraulic return circuits
  • Construction and agricultural equipment
  • Heavy-duty transmission and torque-converter circuits

Selection pitfalls — read before you substitute

  • A return-line element is not a pressure-line element: return cartridges (low-collapse) tolerate roughly 20 bar differential, while BH4HC pressure executions are rated to 210 bar. Installing a low-collapse element in a pressure housing can rupture the media on cold-start spikes.
  • This element has no integral bypass — opening pressure is set by the housing’s reusable bypass valve. Confirm the valve setting (commonly 3.4 bar) is present before fitting.
  • “10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
  • Nitrile (NBR) seals are standard for mineral hydraulic oil but fail early in some phosphate-ester fluids and at sustained high temperature; verify seal compound against the fluid data sheet (fluorocarbon/Viton executions may be required).
  • End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.

Frequently asked questions

What are the dimensions of the 57108 filter element?
The published envelope is 150 mm OD × 451 mm length with a 110 mm inside diameter (5.906 × 17.756 in × 4.331 in ID). Confirm against the housing drawing before ordering.
What replaces the 57108 filter element?
Cross references are being verified for this model — use the inquiry form and the engineering desk will confirm equivalents.
How do I read the 57108 part number?
See the designation decoder above: each segment of 57108 encodes size, line type, filtration grade and media/collapse execution.
Is a same-envelope aftermarket element always a drop-in replacement?
No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.
How often should a hydraulic return-line element be replaced?
Replace at the housing manufacturer’s recommended differential-pressure setting (commonly signalled by a clogging indicator), or on a time-based service interval when no indicator is fitted — never wait for bypass to open continuously, because unfiltered oil then reaches the valves.

Same-envelope elements from other brands

View full interchange →

These 1 catalog element(s) share the 150×451 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

51397 WIX Filters · 10 µm

Other models in the 57xxx series

All 221 →
57000 78×80 mm · 21 µm 57002 68×69 mm · 15 µm 57005 60×229 mm 57023 76×87 mm · 32 µm 57024 52×150 mm · 9 µm 57030 64×99 mm · 35 µm 57031 88×140 mm 57039 94×142 mm · 25 µm 57043 97×234 mm · 3 µm 57044 119×227 mm · 17 µm

Reviewed & verified by the ElementRef engineering desk against WIX Filters (MANN+HUMMEL) on 2026-09-27. Read our editorial & correction policy.