WIX Filters · 51xxx · return line

51468 filter element: specifications & equivalents

The 51468 is a WIX Filters return-line hydraulic filter element, built with paper media, sized 115 × 179 mm OD × length (ID 58 mm), rated at 35 µm class. Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 115 × 179 mm

Inside diameter 58 mm

Filtration rating 35 µm nom.

Media Paper

Line type return

Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-09-27. Confidence score 0.90.

Specification table

Parameter	Value
Filter type	return line
Media	Paper
Filtration rating	35 µm
Rating basis	nominal
Outside diameter OD	115 mm
Inside diameter ID	58 mm
Length	179 mm
End caps	open-ended cartridge element (no baseplate)
Flow direction	outside-in
Integral bypass valve	none (housing/valve-dependent)
Seal material	Nitrile (NBR)
Manufacturer part no.	51468
Source catalog	WIX Filters (MANN+HUMMEL): WIX Filters online product catalog
Last verified	2026-09-27

Sources: WIX Filters (MANN+HUMMEL) — WIX Filters online product catalog — accessed 2026-09-26.

WIX Filters® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized WIX Filters distributor.

Dimensions & series range

Outside diameter	115 mm (4.528 in)
Inside diameter	58 mm (2.283 in)
Overall length	179 mm (7.047 in)

All 115×179 mm interchange elements →

Cross references & equivalents

No catalog-verified cross references yet. This model is in the manual verification queue — request a verified equivalent.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 51468 model number is decoded

51468WIX hydraulic cartridge element part number.
115 mm OD / 58 mm IDCartridge envelope (outside/inside diameter); no mounting thread.
PaperFilter media: Paper.

Typical equipment & applications

Mobile and industrial hydraulic return circuits
Construction and agricultural equipment
Heavy-duty transmission and torque-converter circuits

Selection pitfalls — read before you substitute

A return-line element is not a pressure-line element: return cartridges (BN4HC low-collapse) tolerate roughly 20 bar differential, while BH4HC pressure executions are rated to 210 bar. Installing a low-collapse element in a pressure housing can rupture the media on cold-start spikes.
This element has no integral bypass — opening pressure is set by the housing’s reusable bypass valve. Confirm the valve setting (commonly 3.4 bar) is present before fitting.
“10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
Nitrile (NBR) seals are standard for mineral hydraulic oil but fail early in some phosphate-ester fluids and at sustained high temperature; verify seal compound against the fluid data sheet (fluorocarbon/Viton executions may be required).
End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.

Frequently asked questions

What are the dimensions of the 51468 filter element?

The published envelope is 115 mm OD × 179 mm length with a 58 mm inside diameter (4.528 × 7.047 in × 2.283 in ID). Confirm against the housing drawing before ordering.

What micron rating does 51468 use?

This element is rated 35 µm (nominal class). Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

What replaces the 51468 filter element?

Cross references are being verified for this model — use the inquiry form and the engineering desk will confirm equivalents.

How do I read the 51468 part number?

See the designation decoder above: each segment of 51468 encodes size, line type, filtration grade and media/collapse execution.

Is a same-envelope aftermarket element always a drop-in replacement?

No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.

How often should a hydraulic return-line element be replaced?

Replace at the housing manufacturer’s recommended differential-pressure setting (commonly signalled by a clogging indicator), or on a time-based service interval when no indicator is fitted — never wait for bypass to open continuously, because unfiltered oil then reaches the valves.

Same-envelope elements from other brands

View full interchange →

These 3 catalog element(s) share the 115×179 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

51472 WIX Filters · 25 µm 51476 WIX Filters · 19 µm 51608 WIX Filters

Other models in the 51xxx series

All 306 →

51089 74×144 mm · 32 µm 51096 115×183 mm · 5 µm 51097 114×231 mm · 10 µm 51098 115×227 mm · 23 µm 51113 129×228 mm · 5 µm 51116 94×198 mm · 11 µm 51119 115×229 mm · 23 µm 51120 94×198 mm · 9 µm 51127 88×235 mm · 32 µm 51134 152×216 mm · 10 µm

Reviewed & verified by the ElementRef engineering desk against WIX Filters (MANN+HUMMEL) on 2026-09-27. Read our editorial & correction policy.