STAUFF · Replacement Elements · inline line

SE-125-A-05-B filter element: specifications & equivalents

Q: What are the dimensions of the SE-125-A-05-B filter element?

The published envelope is 60 mm OD × 371 mm length with a 34.2 mm inside diameter (2.362 × 14.606 in × 1.346 in ID). Confirm against the housing drawing before ordering.

The SE-125-A-05-B is a STAUFF inline-line hydraulic filter element, sized 60 × 371 mm OD × length (ID 34.2 mm). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 60 × 371 mm

Inside diameter 34.2 mm

Line type inline

Partially verified. Fit and grade trace to an official interchange document; dimensional values are compiled from 0 aftermarket listing(s) and must be confirmed against the manufacturer housing drawing. Confidence score 0.85.

Micron rating, media type, collapse pressure and seal material are not printed in the STAUFF interchange listing and are pending extraction from STAUFF product data sheets. Verify against the current STAUFF catalog before ordering.

Specification table

Parameter	Value
Filter type	inline line
Outside diameter OD	60 mm
Inside diameter ID	34.2 mm
Length	371 mm
End caps	open-ended cartridge element
Integral bypass valve	none (housing/valve-dependent)
Source catalog	STAUFF: STAUFF Filter Interchange online database (filterinterchange.com)
Last verified	2026-09-28

Sources: STAUFF — STAUFF Filter Interchange online database (filterinterchange.com) — accessed 2026-09-27.

STAUFF® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized STAUFF distributor.

Dimensional drawing

Reference drawing generated from the source values cited on this page — nominal envelope, schematic section, not a manufacturer drawing. The PDF is A3 landscape and vector; the PNG is sized for a WhatsApp preview. Confirm thread, end caps, seal compound and micron/Beta grade against the original element before ordering.

Dimensions & series range

Outside diameter	60 mm (2.362 in)
Inside diameter	34.2 mm (1.346 in)
Overall length	371 mm (14.606 in)

All 60×371 mm interchange elements →

Cross references & equivalents

Equivalent model	Brand	Match level	Note
↔ DHD280A05B	Filtrec	full	Filtrec's official Cross Navigator maps STAUFF SE125A05B to FILTREC DHD280A05B as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade.
↔ 00301605 page in verification queue	UFI	partial	STAUFF Filter Interchange lists 00301605 (HYDAC) as replaced by SE-125-A-05-B. Envelope dimensions are published; media grade and performance data are not — confirm before substituting in cleanliness-critical circuits.
↔ 301605 page in verification queue	Aftermarket	partial	STAUFF Filter Interchange lists 301605 (HYDAC) as replaced by SE-125-A-05-B. Envelope dimensions are published; media grade and performance data are not — confirm before substituting in cleanliness-critical circuits.
↔ 9280M5B000P page in verification queue	Aftermarket	partial	STAUFF Filter Interchange lists 9. 280 M5-B00-0-P (EPE / Bosch-Rexroth Filtration) as replaced by SE-125-A-05-B. Envelope dimensions are published; media grade and performance data are not — confirm before substituting in cleanliness-critical circuits.
↔ ST1303 page in verification queue	Aftermarket	partial	STAUFF Filter Interchange lists ST1303 (ST-FILTER) as replaced by SE-125-A-05-B. Envelope dimensions are published; media grade and performance data are not — confirm before substituting in cleanliness-critical circuits.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

Full chart: STAUFF cross reference chart →

How the SE-125-A-05-B model number is decoded

SE-125-A-05-BSTAUFF replacement element part number per the STAUFF Filter Interchange database.

Typical equipment & applications

Replacement element for OEM hydraulic filter housings

Selection pitfalls — read before you substitute

End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.

Frequently asked questions

What are the dimensions of the SE-125-A-05-B filter element?

The published envelope is 60 mm OD × 371 mm length with a 34.2 mm inside diameter (2.362 × 14.606 in × 1.346 in ID). Confirm against the housing drawing before ordering.

What replaces the SE-125-A-05-B filter element?

1 catalog-confirmed full match(es) (DHD280A05B); 4 partial match(es) requiring parameter review

Is a same-envelope aftermarket element always a drop-in replacement?

No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.

Same-envelope elements from other brands

View full interchange →

These 16 catalog element(s) share the 60×371 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

DHD280A03B Filtrec DHD280A05B Filtrec DHD280A10B Filtrec DHD280A10V Filtrec DHD280A20B Filtrec SE-125-A-03-B STAUFF SE-125-A-03-V STAUFF SE-125-A-05-V STAUFF SE-125-A-10-B STAUFF SE-125-A-10-V STAUFF

Other models in the Replacement Elements series

All 4930 (list page 7/10) →

AD-030-B-125-B 83×193 mm AD-030-B-40-B 83×193 mm AD-030-B-60-B 83×193 mm AD-030-B-80-B 83×193 mm AD-030-E-20-B 83×193 mm AD-033-B-40-B 89×226 mm AD-033-B-60-B 89×226 mm AD-033-B-80-B 89×226 mm AD-033-E-10-B 89×226 mm BL-200-E-10-B 86×62 mm

Reviewed & verified by the ElementRef engineering desk against STAUFF on 2026-09-28. Read our editorial & correction policy.