Filtrec · Filtrec elements · inline line

S141G10 filter element: specifications & equivalents

Q: What are the dimensions of the S141G10 filter element?

The published envelope is 99 mm OD × 210 mm length with a 52 mm inside diameter (3.898 × 8.268 in × 2.047 in ID). Confirm against the housing drawing before ordering.

Q: What micron rating does S141G10 use?

This element is rated 12 µm absolute — β12(c)≥1000. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

The S141G10 is a Filtrec inline-line hydraulic filter element, built with glassfiber media, sized 99 × 210 mm OD × length (ID 52 mm), rated at 12 µm absolute (β12(c)≥1000). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 99 × 210 mm

Inside diameter 52 mm

Filtration rating 12 µm abs.

Beta rating β 12(c)≥1000

Media glassfiber

Line type inline

Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-10-03. Confidence score 0.90.

Dimensions and media grade are taken from Filtrec’s official Cross Navigator, which maps this element to specific competitor part numbers. Filtrec does not publish collapse pressure or seal compound in this API for every code — verify collapse rating, seal execution and bypass setting against the current Filtrec data sheet for the target housing before ordering.

Specification table

Parameter	Value
Filter type	inline line
Media	glassfiber
Filtration rating	12 µm
Rating basis	absolute
Beta ratio	β12(c)≥1000
Outside diameter OD	99 mm
Inside diameter ID	52 mm
Length	210 mm
Integral bypass valve	none (housing/valve-dependent)
Manufacturer part no.	S141G10
Source catalog	Filtrec S.p.A.: Filtrec Cross Navigator
Last verified	2026-10-03

Sources: Filtrec S.p.A. — Filtrec Cross Navigator — accessed 2026-10-03.

Filtrec® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized Filtrec distributor.

Dimensional drawing

Reference drawing generated from the source values cited on this page — nominal envelope, schematic section, not a manufacturer drawing. The PDF is A3 landscape and vector; the PNG is sized for a WhatsApp preview. Confirm thread, end caps, seal compound and micron/Beta grade against the original element before ordering.

Dimensions & series range

Outside diameter	99 mm (3.898 in)
Inside diameter	52 mm (2.047 in)
Overall length	210 mm (8.268 in)

All 99×210 mm interchange elements →

Cross references & equivalents

Equivalent model	Brand	Match level	Note
↔ FBP25M10A page in verification queue	Aftermarket	full	Filtrec's official Cross Navigator maps FBN FBP25M10A to FILTREC S141G10 as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade.
↔ SMP100810G page in verification queue	Aftermarket	full	Filtrec's official Cross Navigator maps NATIONAL FILTERS SMP100810G to FILTREC S141G10 as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

Full chart: Filtrec cross reference chart →

How the S141G10 model number is decoded

G10Filtrec internal media grade code (glassfiber, 12 µm).

Typical equipment & applications

Filtrec aftermarket replacement hydraulic/lube filter element (S family), form-fit-function cross-referenced in Filtrec's official Cross Navigator.

Selection pitfalls — read before you substitute

“10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.

Frequently asked questions

What are the dimensions of the S141G10 filter element?

The published envelope is 99 mm OD × 210 mm length with a 52 mm inside diameter (3.898 × 8.268 in × 2.047 in ID). Confirm against the housing drawing before ordering.

What micron rating does S141G10 use?

This element is rated 12 µm absolute — β12(c)≥1000. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

What replaces the S141G10 filter element?

2 catalog-confirmed full match(es) (FBP25M10A, SMP100810G)

Is a same-envelope aftermarket element always a drop-in replacement?

No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.

Same-envelope elements from other brands

View full interchange →

These 38 catalog element(s) share the 99×210 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

R140C10B Filtrec · 10 µm R140C10BV Filtrec · 10 µm R140C10C Filtrec · 10 µm R140C25B Filtrec · 25 µm R140C25BV Filtrec · 25 µm R140C25C Filtrec · 25 µm R140G06BV Filtrec · 7 µm R140G10B Filtrec · 12 µm R140G25B Filtrec · 22 µm R140M10B Filtrec · 15 µm

Other models in the Filtrec elements series

All 9874 (list page 17/20) →

A105C05 96×60 mm · 5 µm A105C10 96×60 mm · 10 µm A105C25 96×60 mm · 25 µm A105G03 96×60 mm · 5 µm A105G06 96×60 mm · 7 µm A105G10 96×60 mm · 12 µm A105G25 96×60 mm · 22 µm A105T125 96×60 mm · 125 µm A105T250 96×60 mm · 250 µm A105T60 96×60 mm · 60 µm

Reviewed & verified by the ElementRef engineering desk against Filtrec S.p.A. on 2026-10-03. Read our editorial & correction policy.