Filtrec · Filtrec elements · inline line

RHR30S150B filter element: specifications & equivalents

Q: What are the dimensions of the RHR30S150B filter element?

The published envelope is 35 mm OD × 105 mm length with a 12.2 mm inside diameter (1.378 × 4.134 in × 0.480 in ID). Confirm against the housing drawing before ordering.

Q: What micron rating does RHR30S150B use?

This element is rated 150 µm (nominal class). Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

The RHR30S150B is a Filtrec inline-line hydraulic filter element, built with wire-mesh media, sized 35 × 105 mm OD × length (ID 12.2 mm), rated at 150 µm class. Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 35 × 105 mm

Inside diameter 12.2 mm

Filtration rating 150 µm nom.

Media wire-mesh

Line type inline

Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-10-03. Confidence score 0.90.

Dimensions and media grade are taken from Filtrec’s official Cross Navigator, which maps this element to specific competitor part numbers. Filtrec does not publish collapse pressure or seal compound in this API for every code — verify collapse rating, seal execution and bypass setting against the current Filtrec data sheet for the target housing before ordering.

Specification table

Parameter	Value
Filter type	inline line
Media	wire-mesh
Filtration rating	150 µm
Rating basis	nominal
Outside diameter OD	35 mm
Inside diameter ID	12.2 mm
Length	105 mm
Integral bypass valve	none (housing/valve-dependent)
Manufacturer part no.	RHR30S150B
Source catalog	Filtrec S.p.A.: Filtrec Cross Navigator
Last verified	2026-10-03

Sources: Filtrec S.p.A. — Filtrec Cross Navigator — accessed 2026-10-03.

Filtrec® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized Filtrec distributor.

Dimensional drawing

Reference drawing generated from the source values cited on this page — nominal envelope, schematic section, not a manufacturer drawing. The PDF is A3 landscape and vector; the PNG is sized for a WhatsApp preview. Confirm thread, end caps, seal compound and micron/Beta grade against the original element before ordering.

Dimensions & series range

Outside diameter	35 mm (1.378 in)
Inside diameter	12.2 mm (0.480 in)
Overall length	105 mm (4.134 in)

All 35×105 mm interchange elements →

Cross references & equivalents

Equivalent model	Brand	Match level	Note
↔ 0030 R 149 W/HC	HYDAC	partial	Filtrec's official Cross Navigator maps HYDAC 0030R149WHC to FILTREC RHR30S150B as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade. Rated micron differs (149 vs 150 µm) — verify efficiency class and collapse/seal for the housing before substituting.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

Full chart: Filtrec cross reference chart →

How the RHR30S150B model number is decoded

T150Filtrec internal media grade code (wire-mesh, 150 µm).

Typical equipment & applications

Filtrec aftermarket replacement hydraulic/lube filter element (RHR family), form-fit-function cross-referenced in Filtrec's official Cross Navigator.

Selection pitfalls — read before you substitute

“10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.

Frequently asked questions

What are the dimensions of the RHR30S150B filter element?

The published envelope is 35 mm OD × 105 mm length with a 12.2 mm inside diameter (1.378 × 4.134 in × 0.480 in ID). Confirm against the housing drawing before ordering.

What micron rating does RHR30S150B use?

This element is rated 150 µm (nominal class). Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

What replaces the RHR30S150B filter element?

1 partial match(es) requiring parameter review

Is a same-envelope aftermarket element always a drop-in replacement?

No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.

Same-envelope elements from other brands

View full interchange →

These 92 catalog element(s) share the 35×105 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

D102G10YB3 Filtrec · 12 µm D102G10YV3 Filtrec · 12 µm D102G25YB3 Filtrec · 22 µm D102G25YV3 Filtrec · 22 µm D102T125AB3 Filtrec · 125 µm D102T125AV3 Filtrec · 125 µm D102T60AB3 Filtrec · 60 µm D102T60AV3 Filtrec · 60 µm RHR30A10B Filtrec RHR30A10V Filtrec

Other models in the Filtrec elements series

All 9874 (list page 14/20) →

A105C05 96×60 mm · 5 µm A105C10 96×60 mm · 10 µm A105C25 96×60 mm · 25 µm A105G03 96×60 mm · 5 µm A105G06 96×60 mm · 7 µm A105G10 96×60 mm · 12 µm A105G25 96×60 mm · 22 µm A105T125 96×60 mm · 125 µm A105T250 96×60 mm · 250 µm A105T60 96×60 mm · 60 µm

Reviewed & verified by the ElementRef engineering desk against Filtrec S.p.A. on 2026-10-03. Read our editorial & correction policy.