Filtrec · Filtrec elements · inline line
RHR240G03B0/AB1 filter element: specifications & equivalents
The RHR240G03B0/AB1 is a Filtrec inline-line hydraulic filter element, built with glassfiber media, sized 73.5 × 203 mm OD × length (ID 34.5 mm), rated at 5 µm absolute (β5(c)≥1000). Verify against the current manufacturer data sheet before ordering.
Dimensions and media grade are taken from Filtrec’s official Cross Navigator, which maps this element to specific competitor part numbers. Filtrec does not publish collapse pressure or seal compound in this API for every code — verify collapse rating, seal execution and bypass setting against the current Filtrec data sheet for the target housing before ordering.
Specification table
| Parameter | Value |
|---|---|
| Filter type | inline line |
| Media | glassfiber |
| Filtration rating | 5 µm |
| Rating basis | absolute |
| Beta ratio | β5(c)≥1000 |
| Outside diameter OD | 73.5 mm |
| Inside diameter ID | 34.5 mm |
| Length | 203 mm |
| Integral bypass valve | none (housing/valve-dependent) |
| Manufacturer part no. | RHR240G03B0/AB1 |
| Source catalog | Filtrec S.p.A.: Filtrec Cross Navigator |
| Last verified | 2026-10-03 |
Sources: Filtrec S.p.A. — Filtrec Cross Navigator — accessed 2026-10-03.
Filtrec® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized Filtrec distributor.
Dimensional drawing
Dimensions & series range
| Outside diameter | 73.5 mm (2.894 in) |
| Inside diameter | 34.5 mm (1.358 in) |
| Overall length | 203 mm (7.992 in) |
All 74×203 mm interchange elements →
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
|
↔ 0240R003BN4HCKB page in verification queue | Aftermarket | full | Filtrec's official Cross Navigator maps HYDAC 0240R003BN4HCKB to FILTREC RHR240G03B0/AB1 as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade. |
| ↔ 0240 R 003 ON /-KB | HYDAC | partial | Filtrec's official Cross Navigator maps HYDAC 0240R003ONKB to FILTREC RHR240G03B0/AB1 as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade. Rated micron differs (3 vs 5 µm) — verify efficiency class and collapse/seal for the housing before substituting. |
Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
Full chart: Filtrec cross reference chart →
How the RHR240G03B0/AB1 model number is decoded
- G03Filtrec internal media grade code (glassfiber, 5 µm).
Typical equipment & applications
- Filtrec aftermarket replacement hydraulic/lube filter element (RHR family), form-fit-function cross-referenced in Filtrec's official Cross Navigator.
Selection pitfalls — read before you substitute
- “10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
- Fine 5 µm media loads faster and runs at a higher cold Δp than coarser grades — only downgrade cleanliness targets if the system ISO 4406 code allows it.
Frequently asked questions
What are the dimensions of the RHR240G03B0/AB1 filter element?
What micron rating does RHR240G03B0/AB1 use?
What replaces the RHR240G03B0/AB1 filter element?
Is a same-envelope aftermarket element always a drop-in replacement?
Same-envelope elements from other brands
View full interchange →These 205 catalog element(s) share the 74×203 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.
Other models in the Filtrec elements series
All 9874 (list page 13/20) →Reviewed & verified by the ElementRef engineering desk against Filtrec S.p.A. on 2026-10-03. Read our editorial & correction policy.