Filtrec · Filtrec elements · inline line

DHD75G10B filter element: specifications & equivalents

Q: What are the dimensions of the DHD75G10B filter element?

The published envelope is 56.3 mm OD × 170 mm length with a 25.5 mm inside diameter (2.217 × 6.693 in × 1.004 in ID). Confirm against the housing drawing before ordering.

Q: What micron rating does DHD75G10B use?

This element is rated 12 µm absolute — β12(c)≥1000. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

The DHD75G10B is a Filtrec inline-line hydraulic filter element, built with glassfiber media, sized 56.3 × 170 mm OD × length (ID 25.5 mm), rated at 12 µm absolute (β12(c)≥1000). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 56.3 × 170 mm

Inside diameter 25.5 mm

Filtration rating 12 µm abs.

Beta rating β 12(c)≥1000

Media glassfiber

Line type inline

Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-10-03. Confidence score 0.90.

Dimensions and media grade are taken from Filtrec’s official Cross Navigator, which maps this element to specific competitor part numbers. Filtrec does not publish collapse pressure or seal compound in this API for every code — verify collapse rating, seal execution and bypass setting against the current Filtrec data sheet for the target housing before ordering.

Specification table

Parameter	Value
Filter type	inline line
Media	glassfiber
Filtration rating	12 µm
Rating basis	absolute
Beta ratio	β12(c)≥1000
Outside diameter OD	56.3 mm
Inside diameter ID	25.5 mm
Length	170 mm
Integral bypass valve	none (housing/valve-dependent)
Manufacturer part no.	DHD75G10B
Source catalog	Filtrec S.p.A.: Filtrec Cross Navigator
Last verified	2026-10-03

Sources: Filtrec S.p.A. — Filtrec Cross Navigator — accessed 2026-10-03.

Filtrec® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized Filtrec distributor.

Dimensional drawing

Reference drawing generated from the source values cited on this page — nominal envelope, schematic section, not a manufacturer drawing. The PDF is A3 landscape and vector; the PNG is sized for a WhatsApp preview. Confirm thread, end caps, seal compound and micron/Beta grade against the original element before ordering.

Dimensions & series range

Outside diameter	56.3 mm (2.217 in)
Inside diameter	25.5 mm (1.004 in)
Overall length	170 mm (6.693 in)

All 56×170 mm interchange elements →

Cross references & equivalents

Equivalent model	Brand	Match level	Note
↔ D0075A10NHA page in verification queue	Aftermarket	full	Filtrec's official Cross Navigator maps FAI FILTRI D0075A10NHA to FILTREC DHD75G10B as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade.
↔ H075D10N page in verification queue	Aftermarket	full	Filtrec's official Cross Navigator maps SEPARATION TECHNOLOGIES H075D10N to FILTREC DHD75G10B as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade.
↔ HD613/2	MANN-FILTER	full	Filtrec's official Cross Navigator maps MANN + HUMMEL HD6132 to FILTREC DHD75G10B as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade.
↔ 0075 D 010 ON	HYDAC	partial	Filtrec's official Cross Navigator maps HYDAC 0075D010ON to FILTREC DHD75G10B as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade. Rated micron differs (10 vs 12 µm) — verify efficiency class and collapse/seal for the housing before substituting.
↔ HD6004X	MANN-FILTER	partial	MANN-FILTER's online catalog lists DHD75G10B (FILTREC) as a comparison number for HD6004X. Envelope cross-reference; verify micron grade, collapse rating and seal configuration before substituting.
↔ HF29052	Fleetguard	partial	Fleetguard's online catalog lists DHD75G10B as an interchange for HF29052. Envelope cross-reference; verify micron grade, collapse rating and seal configuration before substituting.
↔ PT9493-MPG	Baldwin Filters	partial	Baldwin's Form 561 Number-Finder cross-reference lists DHD75G10B (FILTREC) as replaced by Baldwin PT9493-MPG. Form/fit listing without published performance data — verify micron grade, collapse rating and seal configuration before substituting.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

Full chart: Filtrec cross reference chart →

How the DHD75G10B model number is decoded

G10Filtrec internal media grade code (glassfiber, 12 µm).

Typical equipment & applications

Filtrec aftermarket replacement hydraulic/lube filter element (DHD family), form-fit-function cross-referenced in Filtrec's official Cross Navigator.

Selection pitfalls — read before you substitute

“10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.

Frequently asked questions

What are the dimensions of the DHD75G10B filter element?

The published envelope is 56.3 mm OD × 170 mm length with a 25.5 mm inside diameter (2.217 × 6.693 in × 1.004 in ID). Confirm against the housing drawing before ordering.

What micron rating does DHD75G10B use?

This element is rated 12 µm absolute — β12(c)≥1000. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

What replaces the DHD75G10B filter element?

3 catalog-confirmed full match(es) (D0075A10NHA, H075D10N, HD613/2); 4 partial match(es) requiring parameter review

Is a same-envelope aftermarket element always a drop-in replacement?

No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.

Same-envelope elements from other brands

View full interchange →

These 29 catalog element(s) share the 56×170 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

02.0075 D.10VG.30.HC.E.P Eaton / Internormen · 10 µm DHD75G03B Filtrec · 5 µm DHD75G03B/ESD Filtrec · 5 µm DHD75G03V Filtrec · 5 µm DHD75G03V/ESD Filtrec · 5 µm DHD75G05B Filtrec · 7 µm DHD75G05B/ESD Filtrec · 7 µm DHD75G05V Filtrec · 7 µm DHD75G05V/ESD Filtrec · 7 µm DHD75G10B/ESD Filtrec · 12 µm

Other models in the Filtrec elements series

All 9874 (list page 7/20) →

A105C05 96×60 mm · 5 µm A105C10 96×60 mm · 10 µm A105C25 96×60 mm · 25 µm A105G03 96×60 mm · 5 µm A105G06 96×60 mm · 7 µm A105G10 96×60 mm · 12 µm A105G25 96×60 mm · 22 µm A105T125 96×60 mm · 125 µm A105T250 96×60 mm · 250 µm A105T60 96×60 mm · 60 µm

Reviewed & verified by the ElementRef engineering desk against Filtrec S.p.A. on 2026-10-03. Read our editorial & correction policy.