Filtrec · Filtrec elements · inline line

DHD256G01V filter element: specifications & equivalents

Q: What are the dimensions of the DHD256G01V filter element?

The published envelope is 69 mm OD × 241 mm length with a 34.2 mm inside diameter (2.717 × 9.488 in × 1.346 in ID). Confirm against the housing drawing before ordering.

Q: What micron rating does DHD256G01V use?

This element is rated 4 µm absolute — β4(c)≥1000. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

The DHD256G01V is a Filtrec inline-line hydraulic filter element, built with glassfiber media, sized 69 × 241 mm OD × length (ID 34.2 mm), rated at 4 µm absolute (β4(c)≥1000). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 69 × 241 mm

Inside diameter 34.2 mm

Filtration rating 4 µm abs.

Beta rating β 4(c)≥1000

Media glassfiber

Line type inline

Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-10-03. Confidence score 0.90.

Dimensions and media grade are taken from Filtrec’s official Cross Navigator, which maps this element to specific competitor part numbers. Filtrec does not publish collapse pressure or seal compound in this API for every code — verify collapse rating, seal execution and bypass setting against the current Filtrec data sheet for the target housing before ordering.

Specification table

Parameter	Value
Filter type	inline line
Media	glassfiber
Filtration rating	4 µm
Rating basis	absolute
Beta ratio	β4(c)≥1000
Outside diameter OD	69 mm
Inside diameter ID	34.2 mm
Length	241 mm
Integral bypass valve	none (housing/valve-dependent)
Manufacturer part no.	DHD256G01V
Source catalog	Filtrec S.p.A.: Filtrec Cross Navigator
Last verified	2026-10-03

Sources: Filtrec S.p.A. — Filtrec Cross Navigator — accessed 2026-10-03.

Filtrec® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized Filtrec distributor.

Dimensional drawing

Reference drawing generated from the source values cited on this page — nominal envelope, schematic section, not a manufacturer drawing. The PDF is A3 landscape and vector; the PNG is sized for a WhatsApp preview. Confirm thread, end caps, seal compound and micron/Beta grade against the original element before ordering.

Dimensions & series range

Outside diameter	69 mm (2.717 in)
Inside diameter	34.2 mm (1.346 in)
Overall length	241 mm (9.488 in)

All 69×241 mm interchange elements →

Cross references & equivalents

No catalog-verified cross references yet. This model is in the manual verification queue — request a verified equivalent.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

Full chart: Filtrec cross reference chart →

How the DHD256G01V model number is decoded

G01Filtrec internal media grade code (glassfiber, 4 µm).

Typical equipment & applications

Filtrec aftermarket replacement hydraulic/lube filter element (DHD family), form-fit-function cross-referenced in Filtrec's official Cross Navigator.

Selection pitfalls — read before you substitute

“10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
Fine 4 µm media loads faster and runs at a higher cold Δp than coarser grades — only downgrade cleanliness targets if the system ISO 4406 code allows it.

Frequently asked questions

What are the dimensions of the DHD256G01V filter element?

The published envelope is 69 mm OD × 241 mm length with a 34.2 mm inside diameter (2.717 × 9.488 in × 1.346 in ID). Confirm against the housing drawing before ordering.

What micron rating does DHD256G01V use?

This element is rated 4 µm absolute — β4(c)≥1000. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

What replaces the DHD256G01V filter element?

Cross references are being verified for this model — use the inquiry form and the engineering desk will confirm equivalents.

Is a same-envelope aftermarket element always a drop-in replacement?

No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.

Same-envelope elements from other brands

View full interchange →

These 11 catalog element(s) share the 69×241 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

DHD256G01B Filtrec · 4 µm DHD256G03B Filtrec · 5 µm DHD256G03V Filtrec · 5 µm DHD256G05B Filtrec · 7 µm DHD256G05V Filtrec · 7 µm DHD256G10B Filtrec · 12 µm DHD256G10V Filtrec · 12 µm DHD256G15B Filtrec · 17 µm DHD256G15V Filtrec · 17 µm DHD256G20B Filtrec · 22 µm

Other models in the Filtrec elements series

All 9874 (list page 6/20) →

A105C05 96×60 mm · 5 µm A105C10 96×60 mm · 10 µm A105C25 96×60 mm · 25 µm A105G03 96×60 mm · 5 µm A105G06 96×60 mm · 7 µm A105G10 96×60 mm · 12 µm A105G25 96×60 mm · 22 µm A105T125 96×60 mm · 125 µm A105T250 96×60 mm · 250 µm A105T60 96×60 mm · 60 µm

Reviewed & verified by the ElementRef engineering desk against Filtrec S.p.A. on 2026-10-03. Read our editorial & correction policy.