Filtrec · Filtrec elements · inline line

D811G25A filter element: specifications & equivalents

Q: What are the dimensions of the D811G25A filter element?

The published envelope is 45.5 mm OD × 200 mm length with a 20.5 mm inside diameter (1.791 × 7.874 in × 0.807 in ID). Confirm against the housing drawing before ordering.

Q: What micron rating does D811G25A use?

This element is rated 22 µm absolute — β22(c)≥1000. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

The D811G25A is a Filtrec inline-line hydraulic filter element, built with glassfiber media, sized 45.5 × 200 mm OD × length (ID 20.5 mm), rated at 22 µm absolute (β22(c)≥1000). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 45.5 × 200 mm

Inside diameter 20.5 mm

Filtration rating 22 µm abs.

Beta rating β 22(c)≥1000

Media glassfiber

Line type inline

Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-10-03. Confidence score 0.90.

Dimensions and media grade are taken from Filtrec’s official Cross Navigator, which maps this element to specific competitor part numbers. Filtrec does not publish collapse pressure or seal compound in this API for every code — verify collapse rating, seal execution and bypass setting against the current Filtrec data sheet for the target housing before ordering.

Specification table

Parameter	Value
Filter type	inline line
Media	glassfiber
Filtration rating	22 µm
Rating basis	absolute
Beta ratio	β22(c)≥1000
Outside diameter OD	45.5 mm
Inside diameter ID	20.5 mm
Length	200 mm
Integral bypass valve	none (housing/valve-dependent)
Manufacturer part no.	D811G25A
Source catalog	Filtrec S.p.A.: Filtrec Cross Navigator
Last verified	2026-10-03

Sources: Filtrec S.p.A. — Filtrec Cross Navigator — accessed 2026-10-03.

Filtrec® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized Filtrec distributor.

Dimensional drawing

Reference drawing generated from the source values cited on this page — nominal envelope, schematic section, not a manufacturer drawing. The PDF is A3 landscape and vector; the PNG is sized for a WhatsApp preview. Confirm thread, end caps, seal compound and micron/Beta grade against the original element before ordering.

Dimensions & series range

Outside diameter	45.5 mm (1.791 in)
Inside diameter	20.5 mm (0.807 in)
Overall length	200 mm (7.874 in)

Cross references & equivalents

Equivalent model	Brand	Match level	Note
↔ PR4476	Parker	full	Filtrec's official Cross Navigator maps PARKER PR4476 to FILTREC D811G25A as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade.
↔ SD-015-E-20-B	STAUFF	full	Filtrec's official Cross Navigator maps STAUFF SD015E20B to FILTREC D811G25A as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade.
↔ V3052008K4 page in verification queue	Aftermarket	full	Filtrec's official Cross Navigator maps ARGO-HYTOS V3052008K4 to FILTREC D811G25A as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade.
↔ HD414/2	MANN-FILTER	partial	MANN-FILTER's online catalog lists D811G25A (FILTREC) as a comparison number for HD4142. Envelope cross-reference; verify micron grade, collapse rating and seal configuration before substituting.
↔ PT23083-MPG	Baldwin Filters	partial	Baldwin's Form 561 Number-Finder cross-reference lists D811G25A (FILTREC) as replaced by Baldwin PT23083-MPG. Form/fit listing without published performance data — verify micron grade, collapse rating and seal configuration before substituting.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

Full chart: Filtrec cross reference chart →

How the D811G25A model number is decoded

G25Filtrec internal media grade code (glassfiber, 22 µm).

Typical equipment & applications

Filtrec aftermarket replacement hydraulic/lube filter element (D family), form-fit-function cross-referenced in Filtrec's official Cross Navigator.

Selection pitfalls — read before you substitute

“10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.

Frequently asked questions

What are the dimensions of the D811G25A filter element?

The published envelope is 45.5 mm OD × 200 mm length with a 20.5 mm inside diameter (1.791 × 7.874 in × 0.807 in ID). Confirm against the housing drawing before ordering.

What micron rating does D811G25A use?

This element is rated 22 µm absolute — β22(c)≥1000. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

What replaces the D811G25A filter element?

3 catalog-confirmed full match(es) (PR4476, SD-015-E-20-B, V3052008K4); 2 partial match(es) requiring parameter review

Is a same-envelope aftermarket element always a drop-in replacement?

No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.

Other models in the Filtrec elements series

All 9874 (list page 5/20) →

A105C05 96×60 mm · 5 µm A105C10 96×60 mm · 10 µm A105C25 96×60 mm · 25 µm A105G03 96×60 mm · 5 µm A105G06 96×60 mm · 7 µm A105G10 96×60 mm · 12 µm A105G25 96×60 mm · 22 µm A105T125 96×60 mm · 125 µm A105T250 96×60 mm · 250 µm A105T60 96×60 mm · 60 µm

Reviewed & verified by the ElementRef engineering desk against Filtrec S.p.A. on 2026-10-03. Read our editorial & correction policy.