Filtrec · Filtrec elements · inline line

C224G01 filter element: specifications & equivalents

Q: What are the dimensions of the C224G01 filter element?

The published envelope is 97.5 mm OD × 967 mm length with a 64.5 mm inside diameter (3.839 × 38.071 in × 2.539 in ID). Confirm against the housing drawing before ordering.

Q: What micron rating does C224G01 use?

This element is rated 4 µm absolute — β4(c)≥1000. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

The C224G01 is a Filtrec inline-line hydraulic filter element, built with glassfiber media, sized 97.5 × 967 mm OD × length (ID 64.5 mm), rated at 4 µm absolute (β4(c)≥1000). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 97.5 × 967 mm

Inside diameter 64.5 mm

Filtration rating 4 µm abs.

Beta rating β 4(c)≥1000

Media glassfiber

Line type inline

Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-10-03. Confidence score 0.90.

Dimensions and media grade are taken from Filtrec’s official Cross Navigator, which maps this element to specific competitor part numbers. Filtrec does not publish collapse pressure or seal compound in this API for every code — verify collapse rating, seal execution and bypass setting against the current Filtrec data sheet for the target housing before ordering.

Specification table

Parameter	Value
Filter type	inline line
Media	glassfiber
Filtration rating	4 µm
Rating basis	absolute
Beta ratio	β4(c)≥1000
Outside diameter OD	97.5 mm
Inside diameter ID	64.5 mm
Length	967 mm
Integral bypass valve	none (housing/valve-dependent)
Manufacturer part no.	C224G01
Source catalog	Filtrec S.p.A.: Filtrec Cross Navigator
Last verified	2026-10-03

Sources: Filtrec S.p.A. — Filtrec Cross Navigator — accessed 2026-10-03.

Filtrec® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized Filtrec distributor.

Dimensional drawing

Reference drawing generated from the source values cited on this page — nominal envelope, schematic section, not a manufacturer drawing. The PDF is A3 landscape and vector; the PNG is sized for a WhatsApp preview. Confirm thread, end caps, seal compound and micron/Beta grade against the original element before ordering.

Dimensions & series range

Outside diameter	97.5 mm (3.839 in)
Inside diameter	64.5 mm (2.539 in)
Overall length	967 mm (38.071 in)

All 98×967 mm interchange elements →

Cross references & equivalents

Equivalent model	Brand	Match level	Note
↔ HC9404FCZ39H page in verification queue	Pall	full	Filtrec's official Cross Navigator maps PALL HC9404FCZ39H to FILTREC C224G01 as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade.
↔ HC9404FKZ39H page in verification queue	Pall	full	Filtrec's official Cross Navigator maps PALL HC9404FKZ39H to FILTREC C224G01 as a direct replacement, publishing the FILTREC element's OD/ID/height envelope and media grade.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

Full chart: Filtrec cross reference chart →

How the C224G01 model number is decoded

G01Filtrec internal media grade code (glassfiber, 4 µm).

Typical equipment & applications

Filtrec aftermarket replacement hydraulic/lube filter element (C family), form-fit-function cross-referenced in Filtrec's official Cross Navigator.

Selection pitfalls — read before you substitute

“10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
Fine 4 µm media loads faster and runs at a higher cold Δp than coarser grades — only downgrade cleanliness targets if the system ISO 4406 code allows it.

Frequently asked questions

What are the dimensions of the C224G01 filter element?

The published envelope is 97.5 mm OD × 967 mm length with a 64.5 mm inside diameter (3.839 × 38.071 in × 2.539 in ID). Confirm against the housing drawing before ordering.

What micron rating does C224G01 use?

This element is rated 4 µm absolute — β4(c)≥1000. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

What replaces the C224G01 filter element?

2 catalog-confirmed full match(es) (HC9404FCZ39H, HC9404FKZ39H)

Is a same-envelope aftermarket element always a drop-in replacement?

No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.

Same-envelope elements from other brands

View full interchange →

These 16 catalog element(s) share the 98×967 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

C224G01/ESD Filtrec · 4 µm C224G01V Filtrec · 4 µm C224G01V/ESD Filtrec · 4 µm C224G03 Filtrec · 5 µm C224G03V Filtrec · 5 µm C224G03V/ESD Filtrec · 5 µm C224G06 Filtrec · 7 µm C224G06V Filtrec · 7 µm C224G06V/ESD Filtrec · 7 µm C224G10 Filtrec · 12 µm

Other models in the Filtrec elements series

All 9874 (list page 1/20) →

A105C05 96×60 mm · 5 µm A105C10 96×60 mm · 10 µm A105C25 96×60 mm · 25 µm A105G03 96×60 mm · 5 µm A105G06 96×60 mm · 7 µm A105G10 96×60 mm · 12 µm A105G25 96×60 mm · 22 µm A105T125 96×60 mm · 125 µm A105T250 96×60 mm · 250 µm A105T60 96×60 mm · 60 µm

Reviewed & verified by the ElementRef engineering desk against Filtrec S.p.A. on 2026-10-03. Read our editorial & correction policy.