ElementRef

Eaton / Internormen · 01.E / 01.N / Easy-Fit · pressure line

V6014V1H03 filter element: specifications & equivalents

The V6014V1H03 is a Eaton / Internormen pressure-line hydraulic filter element, built with h-pak media, sized 50.8 × 101.6 mm OD × length. Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 50.8 × 101.6 mm
Media H-Pak
Collapse / burst 207 bar
Line type pressure
Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-09-28. Confidence score 0.90.

Specs come from Eaton's product data hub via its site-search API. The µm retention rating follows ISO 16889 (absolute convention), while the model-code fineness grade is nominal — match both before substituting.

Specification table

ParameterValue
Filter type pressure line
Media H-Pak
Outside diameter OD 50.8 mm
Length 101.6 mm
End caps open-ended cartridge element
Collapse / burst pressure 207 bar
Integral bypass valve none (housing/valve-dependent)
Seal material Fluorocarbon (Viton)
Manufacturer part no. V6014V1H03
Source catalog Eaton: Eaton product data hub via site search API (eaton.com)
Last verified2026-09-28

Sources: Eaton — Eaton product data hub via site search API (eaton.com) — accessed 2026-09-29.

Eaton / Internormen® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized Eaton / Internormen distributor.

Dimensions & series range

Outside diameter50.8 mm (2.000 in)
Overall length101.6 mm (4.000 in)

All 51×102 mm interchange elements →

Cross references & equivalents

Equivalent modelBrandMatch levelNote
↔ BE9801403AV
page in verification queue
AftermarketpartialEaton's filtration cross-reference lists BE9801/4-03AV (Behringer) as an interchange for V6014V1H03. Envelope cross-reference; verify micron grade, delta-P rating and seal configuration before substituting.
↔ HC9801FDP4ZPallpartialEaton's filtration cross-reference lists HC9801FDP4Z (Pall) as an interchange for V6014V1H03. Envelope cross-reference; verify micron grade, delta-P rating and seal configuration before substituting.
↔ HC9801FKP4Z
page in verification queue
PallpartialEaton's filtration cross-reference lists HC9801FKP4Z (Pall) as an interchange for V6014V1H03. Envelope cross-reference; verify micron grade, delta-P rating and seal configuration before substituting.
↔ HF30613FleetguardpartialFleetguard's online catalog lists V6014V1H03 as an interchange for HF30613. Envelope cross-reference; verify micron grade, collapse rating and seal configuration before substituting.
↔ P167270
page in verification queue
DonaldsonpartialEaton's filtration cross-reference lists P167270 (Donaldson) as an interchange for V6014V1H03. Envelope cross-reference; verify micron grade, delta-P rating and seal configuration before substituting.
↔ PT23418-MPGBaldwin FilterspartialBaldwin's Form 561 Number-Finder cross-reference lists V6014V1H03 (VICKERS) as replaced by Baldwin PT23418-MPG. Form/fit listing without published performance data — verify micron grade, collapse rating and seal configuration before substituting.
↔ SBF-9801-4Z3VSchroeder IndustriespartialSchroeder online cross-reference (VICKERS); envelope match — verify grade and seals.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the V6014V1H03 model number is decoded

  • V6014V1H03Eaton V601 Vickers filter element model code (Eaton V601 Vickers Pressure Filter Element).
  • V6014V1H03Eaton catalog number (order code) for the same element.
  • H03Filter fineness grade: nominal rating and media letter.
  • H-PakFilter media execution.
  • 207 barDelta-P resistance class — maximum differential pressure (collapse) rating.
  • Fluorocarbon (Viton)Seal compound.
  • 50.8 mmOuter diameter.
  • 101.6 mmElement height.

Typical equipment & applications

  • Pressure-line hydraulic filters upstream of control valves
  • High-differential-pressure industrial hydraulic circuits
  • Hydraulic power units for steel, paper and power generation

Selection pitfalls — read before you substitute

  • “10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
  • Nitrile (NBR) seals are standard for mineral hydraulic oil but fail early in some phosphate-ester fluids and at sustained high temperature; verify seal compound against the fluid data sheet (fluorocarbon/Viton executions may be required).
  • End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.

Frequently asked questions

What are the dimensions of the V6014V1H03 filter element?
The published envelope is 50.8 mm OD × 101.6 mm length (2.000 × 4.000 in). Confirm against the housing drawing before ordering.
What replaces the V6014V1H03 filter element?
7 partial match(es) requiring parameter review
How do I read the V6014V1H03 part number?
See the designation decoder above: each segment of V6014V1H03 encodes size, line type, filtration grade and media/collapse execution.
Is a same-envelope aftermarket element always a drop-in replacement?
No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.
How often should a hydraulic return-line element be replaced?
Replace at the housing manufacturer’s recommended differential-pressure setting (commonly signalled by a clogging indicator), or on a time-based service interval when no indicator is fitted — never wait for bypass to open continuously, because unfiltered oil then reaches the valves.

Same-envelope elements from other brands

View full interchange →

These 29 catalog element(s) share the 51×102 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

V6011B1C05 Eaton / Internormen V6011B1C10 Eaton / Internormen V6014B1H03 Eaton / Internormen 0060 R 003 ECON2 HYDAC · 3 µm 0060 R 003 ON HYDAC · 3 µm 0060 R 003 ON /-B6 HYDAC · 3 µm 0060 R 003 ON /-KB HYDAC · 3 µm 0060 R 005 ON HYDAC · 5 µm 0060 R 005 ON /-B6 HYDAC · 5 µm 0060 R 010 ON HYDAC · 10 µm

Other models in the 01.E / 01.N / Easy-Fit series

All 3329 →
01.1910.40G.16.E.O.SON 44×110 mm 01.20213.130G.E.O 102×202 mm 01.21657.25VG.10.B.N.IS09 140×459 mm 01.41542.25VG.16.B.N.IS09 90×558 mm · 20 µm 01.AS 180.250G.-.E.T.- 80×315 mm · 250 µm 01.AS 180.40G.-.E.T.- 80×315 mm · 40 µm 01.AS 180.80G.-.E.T.- 80×315 mm · 80 µm 01.AS 220.130G.-.B.-.- 79×274 mm · 130 µm 01.AS 220.250G.-.B.-.- 79×274 mm · 250 µm 01.AS 220.25G.-.B.-.- 79×274 mm · 25 µm

Reviewed & verified by the ElementRef engineering desk against Eaton on 2026-09-28. Read our editorial & correction policy.