ElementRef

Eaton / Internormen · 01.E / 01.N / Easy-Fit · inline line

02.0330R.3VG.30.HC.S.P filter element: specifications & equivalents

The 02.0330R.3VG.30.HC.S.P is a Eaton / Internormen inline-line hydraulic filter element, built with glass fiber fleece (vg) media, sized 95 × 195 mm OD × length, rated at 5 µm absolute. Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 95 × 195 mm
Filtration rating 5 µm abs.
Media Glass fiber fleece (VG)
Collapse / burst 30 bar
Line type inline
Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-09-28. Confidence score 0.90.

Specs come from Eaton's product data hub via its site-search API. The µm retention rating follows ISO 16889 (absolute convention), while the model-code fineness grade is nominal — match both before substituting.

Specification table

ParameterValue
Filter type inline line
Media Glass fiber fleece (VG)
Filtration rating 5 µm
Rating basis absolute
Outside diameter OD 95 mm
Length 195 mm
End caps open-ended cartridge element
Collapse / burst pressure 30 bar
Integral bypass valve none (housing/valve-dependent)
Seal material Nitrile (Buna-N)
Manufacturer part no. 307308
Source catalog Eaton: Eaton product data hub via site search API (eaton.com)
Last verified2026-09-28

Sources: Eaton — Eaton product data hub via site search API (eaton.com) — accessed 2026-09-29.

Eaton / Internormen® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized Eaton / Internormen distributor.

Dimensions & series range

Outside diameter95 mm (3.740 in)
Overall length195 mm (7.677 in)

All 95×195 mm interchange elements →

Cross references & equivalents

Equivalent modelBrandMatch levelNote
↔ 0330 R 003 BN4HCHYDACpartialEaton's filtration cross-reference lists 0330R003BN4HC (Hydac) as an interchange for 02.0330R.3VG.30.HC.S.P. Envelope cross-reference; verify micron grade, delta-P rating and seal configuration before substituting.
↔ 0330 R 003 ONHYDACpartialEaton's filtration cross-reference lists 0330R003ON (Hydac) as an interchange for 02.0330R.3VG.30.HC.S.P. Envelope cross-reference; verify micron grade, delta-P rating and seal configuration before substituting.
↔ 0330R003ONHCB
page in verification queue
AftermarketpartialEaton's filtration cross-reference lists 0330R003ONHC/-B (Hydac) as an interchange for 02.0330R.3VG.30.HC.S.P. Envelope cross-reference; verify micron grade, delta-P rating and seal configuration before substituting.
↔ 938281Q
page in verification queue
AftermarketpartialEaton's filtration cross-reference lists 938281Q (Parker) as an interchange for 02.0330R.3VG.30.HC.S.P. Envelope cross-reference; verify micron grade, delta-P rating and seal configuration before substituting.
↔ SBF-0330R-Z3BSchroeder IndustriespartialSchroeder online cross-reference (INTERNORMEN); envelope match — verify grade and seals.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 02.0330R.3VG.30.HC.S.P model number is decoded

  • 02.0330R.3VG.30.HC.S.PEaton Easy-Fit filter element model code (Eaton Easy-Fit Exchange Filter Element).
  • 307308Eaton catalog number (order code) for the same element.
  • 3 VGFilter fineness grade: nominal rating and media letter.
  • 5 µmISO 16889 multipass retention rating as published by Eaton.
  • Glass fiber fleece (VG)Filter media execution.
  • 30 barDelta-P resistance class — maximum differential pressure (collapse) rating.
  • Nitrile (Buna-N)Seal compound.
  • 95 mmOuter diameter.
  • 195 mmElement height.

Typical equipment & applications

  • Medium-pressure in-line and lubrication circuits
  • Spin-on and exchange element replacements

Selection pitfalls — read before you substitute

  • “10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
  • Nitrile (NBR) seals are standard for mineral hydraulic oil but fail early in some phosphate-ester fluids and at sustained high temperature; verify seal compound against the fluid data sheet (fluorocarbon/Viton executions may be required).
  • Fine 5 µm media loads faster and runs at a higher cold Δp than coarser grades — only downgrade cleanliness targets if the system ISO 4406 code allows it.
  • End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.

Frequently asked questions

What are the dimensions of the 02.0330R.3VG.30.HC.S.P filter element?
The published envelope is 95 mm OD × 195 mm length (3.740 × 7.677 in). Confirm against the housing drawing before ordering.
What micron rating does 02.0330R.3VG.30.HC.S.P use?
This element is rated 5 µm absolute. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.
What replaces the 02.0330R.3VG.30.HC.S.P filter element?
5 partial match(es) requiring parameter review
How do I read the 02.0330R.3VG.30.HC.S.P part number?
See the designation decoder above: each segment of 020330R3VG30HCSP encodes size, line type, filtration grade and media/collapse execution.
Is a same-envelope aftermarket element always a drop-in replacement?
No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.
How often should a hydraulic return-line element be replaced?
Replace at the housing manufacturer’s recommended differential-pressure setting (commonly signalled by a clogging indicator), or on a time-based service interval when no indicator is fitted — never wait for bypass to open continuously, because unfiltered oil then reaches the valves.

Same-envelope elements from other brands

View full interchange →

These 93 catalog element(s) share the 95×195 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

02.0330 R.10P.30.S.P Eaton / Internormen · 10 µm 02.0330 R.10VG.30.HC.E.P Eaton / Internormen · 10 µm 02.0330 R.10VG.30.HC.E.V Eaton / Internormen · 10 µm 02.0330R.10VG.30.HC.S.P Eaton / Internormen · 10 µm 02.0330R.20VG.30.HC.S.P Eaton / Internormen · 20 µm 02.0330 R.25G.30.HC.E.V Eaton / Internormen · 25 µm 02.0330R.25G.30.HC.S.P Eaton / Internormen · 25 µm 02.0330 R.50G.30.HC.S.P Eaton / Internormen · 50 µm 02.0330 R.50G.30.S.P Eaton / Internormen · 50 µm 02.0330 R.6VG.30.HC.E.P Eaton / Internormen · 7 µm

Other models in the 01.E / 01.N / Easy-Fit series

All 3329 →
01.1910.40G.16.E.O.SON 44×110 mm 01.20213.130G.E.O 102×202 mm 01.21657.25VG.10.B.N.IS09 140×459 mm 01.41542.25VG.16.B.N.IS09 90×558 mm · 20 µm 01.AS 180.250G.-.E.T.- 80×315 mm · 250 µm 01.AS 180.40G.-.E.T.- 80×315 mm · 40 µm 01.AS 180.80G.-.E.T.- 80×315 mm · 80 µm 01.AS 220.130G.-.B.-.- 79×274 mm · 130 µm 01.AS 220.250G.-.B.-.- 79×274 mm · 250 µm 01.AS 220.25G.-.B.-.- 79×274 mm · 25 µm

Reviewed & verified by the ElementRef engineering desk against Eaton on 2026-09-28. Read our editorial & correction policy.