ElementRef

Eaton / Internormen · 01.E / 01.N / Easy-Fit · pressure line

01.E 240.25G.HR.E.P.- filter element: specifications & equivalents

The 01.E 240.25G.HR.E.P.- is a Eaton / Internormen pressure-line hydraulic filter element, built with stainless steel wire mesh (g) media, sized 60 × 230 mm OD × length, rated at 25 µm absolute. Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 60 × 230 mm
Filtration rating 25 µm abs.
Media Stainless steel wire mesh (G)
Collapse / burst 160 bar
Line type pressure
Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-09-28. Confidence score 0.90.

Specs come from Eaton's product data hub via its site-search API. The µm retention rating follows ISO 16889 (absolute convention), while the model-code fineness grade is nominal — match both before substituting.

Specification table

ParameterValue
Filter type pressure line
Media Stainless steel wire mesh (G)
Filtration rating 25 µm
Rating basis absolute
Outside diameter OD 60 mm
Length 230 mm
End caps open-ended cartridge element
Collapse / burst pressure 160 bar
Integral bypass valve none (housing/valve-dependent)
Seal material Nitrile (Buna-N)
Manufacturer part no. 300192
Source catalog Eaton: Eaton product data hub via site search API (eaton.com)
Last verified2026-09-28

Sources: Eaton — Eaton product data hub via site search API (eaton.com) — accessed 2026-09-29.

Eaton / Internormen® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized Eaton / Internormen distributor.

Dimensions & series range

Outside diameter60 mm (2.362 in)
Overall length230 mm (9.055 in)

All 60×230 mm interchange elements →

Cross references & equivalents

Equivalent modelBrandMatch levelNote
↔ SN-070-W-25-BSTAUFFpartialSTAUFF Filter Interchange lists 01.E240. 25G.HR.E.P (INTERNORMEN) as replaced by SN-070-W-25-B. Envelope dimensions are published; media grade and performance data are not — confirm before substituting in cleanliness-critical circuits.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 01.E 240.25G.HR.E.P.- model number is decoded

  • 01.E 240.25G.HR.E.P.-Eaton 01.E Pressure filter element model code (Eaton 01.E Pressure Filter Element).
  • 300192Eaton catalog number (order code) for the same element.
  • 25 GFilter fineness grade: nominal rating and media letter.
  • 25 µmISO 16889 multipass retention rating as published by Eaton.
  • Stainless steel wire mesh (G)Filter media execution.
  • 160 barDelta-P resistance class — maximum differential pressure (collapse) rating.
  • Nitrile (Buna-N)Seal compound.
  • 60 mmOuter diameter.
  • 230 mmElement height.

Typical equipment & applications

  • Pressure-line hydraulic filters upstream of control valves
  • High-differential-pressure industrial hydraulic circuits
  • Hydraulic power units for steel, paper and power generation

Selection pitfalls — read before you substitute

  • “10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
  • Nitrile (NBR) seals are standard for mineral hydraulic oil but fail early in some phosphate-ester fluids and at sustained high temperature; verify seal compound against the fluid data sheet (fluorocarbon/Viton executions may be required).
  • End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.

Frequently asked questions

What are the dimensions of the 01.E 240.25G.HR.E.P.- filter element?
The published envelope is 60 mm OD × 230 mm length (2.362 × 9.055 in). Confirm against the housing drawing before ordering.
What micron rating does 01.E 240.25G.HR.E.P.- use?
This element is rated 25 µm absolute. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.
What replaces the 01.E 240.25G.HR.E.P.- filter element?
1 partial match(es) requiring parameter review
How do I read the 01.E 240.25G.HR.E.P.- part number?
See the designation decoder above: each segment of 01E24025GHREP encodes size, line type, filtration grade and media/collapse execution.
Is a same-envelope aftermarket element always a drop-in replacement?
No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.
How often should a hydraulic return-line element be replaced?
Replace at the housing manufacturer’s recommended differential-pressure setting (commonly signalled by a clogging indicator), or on a time-based service interval when no indicator is fitted — never wait for bypass to open continuously, because unfiltered oil then reaches the valves.

Same-envelope elements from other brands

View full interchange →

These 74 catalog element(s) share the 60×230 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

01.E 240.10G.30.E.P.- Eaton / Internormen · 10 µm 01.E 240.10G.HR.E.P.- Eaton / Internormen · 10 µm 01.E 240.10G.HR.E.V.- Eaton / Internormen · 10 µm 01.E 240.10G.HR.E.V.VA Eaton / Internormen · 10 µm 01.E 240.10VG.30.E.P.- Eaton / Internormen · 10 µm 01.E 240.10VG.30.E.P.VA Eaton / Internormen · 10 µm 01.E 240.10VG.30.E.V.- Eaton / Internormen · 10 µm 01.E 240.10VG.30.E.V.IS06 Eaton / Internormen · 10 µm 01.E 240.10VG.30.E.V.VA Eaton / Internormen · 10 µm 01.E 240.10VG.30.E.V.VA.IS08 Eaton / Internormen · 10 µm

Other models in the 01.E / 01.N / Easy-Fit series

All 3329 →
01.1910.40G.16.E.O.SON 44×110 mm 01.20213.130G.E.O 102×202 mm 01.21657.25VG.10.B.N.IS09 140×459 mm 01.41542.25VG.16.B.N.IS09 90×558 mm · 20 µm 01.AS 180.250G.-.E.T.- 80×315 mm · 250 µm 01.AS 180.40G.-.E.T.- 80×315 mm · 40 µm 01.AS 180.80G.-.E.T.- 80×315 mm · 80 µm 01.AS 220.130G.-.B.-.- 79×274 mm · 130 µm 01.AS 220.250G.-.B.-.- 79×274 mm · 250 µm 01.AS 220.25G.-.B.-.- 79×274 mm · 25 µm

Reviewed & verified by the ElementRef engineering desk against Eaton on 2026-09-28. Read our editorial & correction policy.